Why Beveltools Handles Hardened Cut Edges Better

If you work with laser- or plasma-cut steel, you know the problem. The edge looks clean, but the moment you try to bevel or round it, your tool struggles. Discs wear out fast, cutters go dull, and the job takes longer than it should. In this blog we explain why that happens, and why a Beveltools machine makes the job much easier, with cutters designed with care down to the last detail, from high-quality tungsten carbide to the geometry of every tooth, and accessories that support every step.

Why cut edges get so hard

Plasma and laser cutting use heat to cut steel. The heat melts the steel along the cut line. Right next to the cut, the steel gets extremely hot, often far above 723 °C.

723 °C is an important number for steel. Above this temperature, the inner structure of the steel changes. When the heat source moves on, the cold plate around the edge pulls the heat away very quickly. This fast cooling works like quenching: it "locks" the steel into a very hard structure called martensite.

The result is a thin, hard outer layer on the cut edge, often harder than the rest of the plate. How hard it gets depends on the steel: the more carbon it contains, the stronger the effect. Mild steel hardens less than higher-carbon grades, but the hardened layer still shows up on many common steels. This layer is exactly what makes bevelling, rounding and deburring so difficult.

Why grinders struggle on hardened edges

Many workshops still use an angle grinder for this job. On a hardened edge, that means:

  • Fast disc wear. The hard layer eats through abrasive discs quickly.
  • Uneven results. It is hard to keep the same angle or radius by hand along the whole edge.
  • Dust, sparks and noise. Grinding creates a lot of dust and sparks, and it is tiring work.
  • More time. Each edge takes longer, and you often need extra passes.

A different approach: cut, don't grind

That is why we chose a different way. A Beveltools machine does not grind the edge away. It cuts it, with a cutter made from tungsten carbide (WC), one of the hardest materials used for cutting tools. A hard material keeps its sharp edge, even when it meets the hardened layer of a laser- or plasma-cut edge.

But material is only half of the story. The other half is the shape of the cutter. Think of a knife and a block of butter. Push the flat back of the knife into the butter, and you need a lot of force while the butter piles up in front of it. Turn the knife so the sharp, angled edge leads, and it slides right through.

Our cutters work the same way. Each tooth meets the metal at an angle, so it lifts the metal into a chip that slides away, instead of pushing and crushing it. That means less force, less friction and less heat. The cut is smoother and quieter, the edge stays the same from start to finish, and there is no grinding dust and far fewer sparks.

We keep improving

A good tool can always get better, so we keep looking for even better solutions. By listening to the people who use our machines every day, we improved the cutter geometry again. The result is our 4.0 line: new cutters and machines built on everything we learned. The new cutters take bigger bites, run with less friction, remove chips more cleanly, work more quietly and steadily, and last significantly longer.*

We also looked beyond the cutter itself. The easier the cutter's job, the longer it lasts. So we developed three accessories that support the process: the Prep Disc, Bevel Wax and the Clean Disc. You don't always need all three; it depends on your material and the result you want. When you do use them all, the order is: prep, wax, clean.

Step 1: Prep

Before bevelling, a quick pass with the Prep Disc removes the hard outer layer left by laser and plasma cutting and straightens the edge. This is a short preparation step, not the main job: the disc only takes off the thin hardened skin, and the actual bevelling or rounding is still done by the cutter. Because the cutter no longer has to fight that hard layer, it works more efficiently and wears less.

Step 2: Wax

Just before and while you bevel, Bevel Wax lubricates the cutter without dripping or spilling. It works on steel and stainless steel, where liquid oils are not suitable, and makes the cut smoother while extending cutter life.

Step 3: Clean

After bevelling, the Clean Disc removes rust, paint and other dirt from the surface. Its open structure keeps it from clogging, so it keeps working cleanly from start to finish.

The result

Hardened cut edges are tough on every tool. With a hard tungsten carbide cutter, a smarter geometry and the right accessories when you need them, they become just another edge: bevelled or rounded faster, cleaner and with less wear. And we are not done yet. We keep working on the next improvement.

Better tools. Better results.

Want to see it on your own material? Contact us at info@beveltools.com.

*Based on customer experiences.